« previous next »
Pages: [1]   Go Down

Author Topic: Remington 700 45-70 conversion?  (Read 1174 times)

0 Members and 1 Guest are viewing this topic.

Offline Aardvark

  • GBO Supporter
  • Trade Count: (10)
  • Contributor
  • *****
  • Posts: 391
  • Gender: Male
Remington 700 45-70 conversion?
« on: January 20, 2007, 03:54:59 AM »
 What would be involved in rebarreling an early 700 ADL to 45-70...Present caliber is 30-06.
Logged
/^\__/^\
((*)   (*))
 ``(oo) ``
(V\/vv\/V)

Offline huntswithdogs

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 999
Re: Remington 700 45-70 conversion?
« Reply #1 on: January 22, 2007, 05:31:26 AM »
You're goona have to have some boltface altering done. 06 is rimless and 45/70 rimmed. You may have to have the stock inletted some also.

HWD
Logged

Offline Aardvark

  • GBO Supporter
  • Trade Count: (10)
  • Contributor
  • *****
  • Posts: 391
  • Gender: Male
Re: Remington 700 45-70 conversion?
« Reply #2 on: January 22, 2007, 05:55:05 AM »
I have found some more info...The Remington bolt face is not large enough to expand to 45-70 dimension...Even most 98 Mausers are not but the Siamese Mauser is as is the Enfield, and probably the Mosin Nagant, as these are rimmed cartridge firearms...Oh well, back to the drawing board.
Logged
/^\__/^\
((*)   (*))
 ``(oo) ``
(V\/vv\/V)

Offline kyelkhunter3006

  • GBO Supporter
  • Trade Count: (20)
  • Senior Member
  • *****
  • Posts: 1576
  • Gender: Male
Re: Remington 700 45-70 conversion?
« Reply #3 on: January 22, 2007, 10:37:05 AM »
I've seen several 45-70 Enfields on gunbroker.com recently.  If you don't mind the Enfield, that's probably your best bet in a bolt action.
Logged

Offline Aardvark

  • GBO Supporter
  • Trade Count: (10)
  • Contributor
  • *****
  • Posts: 391
  • Gender: Male
Re: Remington 700 45-70 conversion?
« Reply #4 on: January 22, 2007, 04:55:14 PM »
 I think I'm going with the Siamese Mauser...I have a line on acquiring one in good enough shape...I will probably send it to ER Shaw for the barrel/action work...I had them do a M98 in 280 Rem and it is sweet.
Logged
/^\__/^\
((*)   (*))
 ``(oo) ``
(V\/vv\/V)

Offline kyelkhunter3006

  • GBO Supporter
  • Trade Count: (20)
  • Senior Member
  • *****
  • Posts: 1576
  • Gender: Male
Re: Remington 700 45-70 conversion?
« Reply #5 on: January 23, 2007, 07:54:14 AM »
Shaw does good work, and the prices are reasonable too.  I talked to them back in Sept. about a project, and the turn-around was running about 20 weeks, with 13 of them being until they notified you to ship the gun to them.  I've seen a couple Siamese 45-70's on gunbroker too, prices were in the $500's or higher, but they were kind of rough looking.
Logged

Offline lrs

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 672
Re: Remington 700 45-70 conversion?
« Reply #6 on: January 23, 2007, 02:38:37 PM »
I have a 45-70 built on a siamese mauser.  I would highly recommend one.  I have been very pleased with mine.  Good luck on this.
Logged
" we are screwed "

Offline Nobade

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1927
Re: Remington 700 45-70 conversion?
« Reply #7 on: January 23, 2007, 03:22:24 PM »
If you want to do this on a 700, just start with any magnum action, and rebarrel it for .458X2in. It'll have the same capacity as a 45-70, but will feed and work properly.
Logged
"Give me a lever long enough, and a place to stand, and I'll break the lever."

Offline StrawHat

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 550
  • Gender: Male
Re: Remington 700 45-70 conversion?
« Reply #8 on: January 26, 2007, 02:50:14 AM »
Along the lines of what nobade said, but save some money and get the 458 Mag.

I had a M98 so chambered and used it with black powder and lead bullets.  In reality, a belted 45-90.

A lot of fun but someone else wanted it more than I did.

I also have the Siamese and comparing the two, the M98 seemed to have less felt recoil with stouter loads (not comparing to magnum loads).

Logged
"Nothing in life is so exhilarating as to be shot at without result"  Winston Churchill

"A law without a punishment is merely advice."  anonymous

Offline coyote trapper1928

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 496
    • North Country Outdoors
Re: Remington 700 45-70 conversion?
« Reply #9 on: January 26, 2007, 04:47:10 AM »
Can you rebarrel a 458 winchester magnum to 45-70 ?
Logged
coyote trapper1928

Offline EsoxLucius

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 601
  • Gender: Male
Re: Remington 700 45-70 conversion?
« Reply #10 on: January 27, 2007, 04:23:37 AM »
Quote from: coyote trapper1928 on January 26, 2007, 04:47:10 AM
Can you rebarrel a 458 winchester magnum to 45-70 ?
Why?  As alluded to above, any bolt action rifle chambered for rimless or belted cartridges make a poor candidate for rimmed conversion.  A 450 Marlin would work better, but all one has to do is download the 458 WM to get to that level.
Logged
We learn something new everyday whether we want to or not.
Pages: [1]   Go Up
« previous next »