« previous next »
Pages: [1]   Go Down

Author Topic: Van Horn barrels for handi rifles  (Read 2066 times)

0 Members and 1 Guest are viewing this topic.

Offline lee1954

  • GBO Supporter
  • Trade Count: (2)
  • Avid Poster
  • *****
  • Posts: 232
  • Gender: Male
Van Horn barrels for handi rifles
« on: May 17, 2009, 09:09:03 AM »
 I saw on the TC link that Van Horn makes tc barrels , someone said handi barrels too..
 I couldn't find a Van Horn webb sight..
 Do most folks have good luck with H&R barrels, and I only hear about the unhappy ones?
Or should I just buy a second handi to get the barrel? ??? 
Logged

Offline myarmor

  • Trade Count: (46)
  • Senior Member
  • *****
  • Posts: 3239
  • Gender: Male
Re: Van Horn barrels
« Reply #1 on: May 17, 2009, 09:18:34 AM »
Green Mountain use to make some for NEF/H&R ,  but if memory serves me correctly Marlin took up making H&R barrels. Remington evidently has a new hammer forge set up to start running barrels but isn't online yet from what I hear.
Don't know much about Van Horn...




-Aaron
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43304
  • Gender: Male
Re: Van Horn barrels
« Reply #2 on: May 17, 2009, 11:54:00 AM »
Here's the Van Horn website, nothing there about H&Rs and I've never seen one mentioned here.

Tim

http://www.mygunroom.com/dvgunshop/

http://www.mygunroom.com/dvgunshop/calibers.htm
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Lefty Dude

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 221
  • Gender: Male
Re: Van Horn barrels
« Reply #3 on: May 17, 2009, 01:49:05 PM »
Dave Vanhorn has made several Custom TC barrel over the past 25 years. His workmanship is excellent. He has also made several Custom Rifles for my Family. He buys his TC Lug assy. from TC and then welds his barrels for the completed unit. If he can get the Handi-Rifle Lug he can make a custom barrel that is far superior to the Handi/Remington barrel. The last Rifle he built for me was with a ER Shaw match barrel, it is a 22 Hornet on a 24" rifle barrel. One of my TC Rifles is shown on his web-site. It is a 270 Ingram (223 necked-up to 270) and is stocked with a Left-Hand Harry Lawson one hole rear stock with matching for-piece. This piece shoots a sub-MOA group with a 90 ga. Sierra HP varmit 270 spitzer. This is very close to the 6.8mm SPC Remington.

Contact him, with your requirements. If he does the work it will be the most accurate Handi you will own. ;)
Logged

Offline mauser98us

  • GBO Supporter
  • Trade Count: (40)
  • Senior Member
  • *****
  • Posts: 1565
  • Gender: Male
  • 10 mm junkie and Whelan wacko
Re: Van Horn barrels
« Reply #4 on: May 17, 2009, 05:46:36 PM »
His business is not too far from me. I have talked to him and he will do rechambers on Handis
Logged

Offline lee1954

  • GBO Supporter
  • Trade Count: (2)
  • Avid Poster
  • *****
  • Posts: 232
  • Gender: Male
Re: Van Horn barrels
« Reply #5 on: May 17, 2009, 06:38:18 PM »
OK, thanks very much,   don't think H&R would sell him lugs,  but I'll call  Van Horn this week,,
The  H&R  lug should be less work to make,,, but I bet there not eager for work
                                                        Thanks again   DanLee
Logged

Offline MSP Ret

  • GBO Supporter
  • Trade Count: (173)
  • Senior Member
  • *****
  • Posts: 8940
  • Gender: Male
Re: Van Horn barrels
« Reply #6 on: May 18, 2009, 05:36:46 AM »
should be no problem to get a lug, just buy the cheapest used shotgun barrel you can find and use the lug from it....<><....:)
Logged
"Giving up your gun to someone else on demand is called surrender. It means that you have given up your ability to protect yourself to a power that is greater than you." - David Yeagley

Offline lee1954

  • GBO Supporter
  • Trade Count: (2)
  • Avid Poster
  • *****
  • Posts: 232
  • Gender: Male
Re: Van Horn barrels
« Reply #7 on: May 18, 2009, 07:06:48 AM »
I called Van Horn    and  good news  they make very good shooting  handi rifle barrels.  you have to send them the receiver  and for $425 you'll have a completed barrel .. 
     
    Most any Cal.  that will work on the frame  (wildcats  Cal. too)..

        He said that he just made a  Handi 22 - 250  barrel  that out shoots the   rem. or winchester bolts  action of the handi's owner.
     
Thanks for the good  input and help . There page has nicelooking guns
 
I need to supercharge my piggy bank   --I want a tackdriver wildcat  handi !! 
                                                                        Dan  Lee
Logged

Offline mtbugle

  • Trade Count: (32)
  • Contributor
  • ***
  • Posts: 355
  • Gender: Male
Re: Van Horn barrels for handi rifles
« Reply #8 on: May 19, 2009, 09:48:11 AM »
was there any mention of how long wait time would be?
thanks don.
Logged

Offline lee1954

  • GBO Supporter
  • Trade Count: (2)
  • Avid Poster
  • *****
  • Posts: 232
  • Gender: Male
Re: Van Horn barrels for handi rifles
« Reply #9 on: May 19, 2009, 01:12:35 PM »
Sorry   I'll get that info and post tomarrow.
   


Unless someone else might knows.


the price was them doing everything as I understood


Lefty Dude  do you recall the avarage time it took to get a barrel make  at VanHorn ?
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43304
  • Gender: Male
Re: Van Horn barrels for handi rifles
« Reply #10 on: May 19, 2009, 01:22:03 PM »
That's actually not a bad price if that includes the donor underlug and barrel blank. Stubs cost $250-$300 plus the donor underug and barrel blank. Rebores/rechambers run about the same plus the cost of the original barrel.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline canon6

  • GBO Supporter
  • Trade Count: (119)
  • Senior Member
  • *****
  • Posts: 1508
  • Gender: Male
Re: Van Horn barrels for handi rifles
« Reply #11 on: May 19, 2009, 01:29:04 PM »
That is very interesting. I still long for a 6.5x30-30, just because.120 gr NBT at 2800 is a killer combo.   Doug
Logged
a armed man is his own master

Offline Lefty Dude

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 221
  • Gender: Male
Re: Van Horn barrels for handi rifles
« Reply #12 on: May 19, 2009, 03:57:29 PM »
Consider a .225 Winchester chambering, it would make a great Handi Custom barrel. ;)

Dave has the reamer and has done many TC's in the caliber.
Logged

Offline lee1954

  • GBO Supporter
  • Trade Count: (2)
  • Avid Poster
  • *****
  • Posts: 232
  • Gender: Male
Re: Van Horn barrels for handi rifles
« Reply #13 on: May 20, 2009, 01:16:30 PM »
I called today and they need a  donar lug --- and it take about 6 week for Van Horn. to make a handi barrel.

 So when I send the receiver in to get my .357  -I'll get a extra  shotgun barrel too.

 
 Am I right to asume It take about the same time  to get multiple as one barrel ?
 
 I read that other shops do barrles from stubs also.

By far, sending it in to H&R is the lowest cost for new ... But I think I'd like a costom barrel.

 

 
 
Logged

Offline trotterlg

  • GBO Supporter
  • Trade Count: (36)
  • Senior Member
  • *****
  • Posts: 3978
  • Gender: Male
Re: Van Horn barrels for handi rifles
« Reply #14 on: May 20, 2009, 01:45:37 PM »
For a total cost of $500.00 I hope they put a really really good barrel on it!  Larry
Logged
A gun is just like a parachute, if you ever really need one, nothing else will do.

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43304
  • Gender: Male
Re: Van Horn barrels for handi rifles
« Reply #15 on: May 20, 2009, 02:35:30 PM »
Turn around time will depend mainly on barrel availability, some have got orders back in 30 days, others have been waiting for several months.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline John Boy

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 381
Re: Van Horn barrels for handi rifles
« Reply #16 on: May 23, 2009, 03:28:58 PM »
With Green Mountain having made barrels for the NEF/H&R - why not give them a call and see what they have or can do.  Personally, the GM barrels on my BC are nothing but pure accuracy
Logged
Regards
John Boy

Offline mo.hunter

  • Trade Count: (0)
  • Member
  • *
  • Posts: 20
Re: Van Horn barrels for handi rifles
« Reply #17 on: May 25, 2009, 12:28:50 AM »
I would love to have a 24" heavey sporter in 6.5 creedmor, deer and coyotes beware!!! ;D
Logged
Pages: [1]   Go Up
« previous next »