Cast Bullet Discussion

Pages: 1 ... 5 6 7 8 9 [10] 11 12 13 14 15 ... 86 Go Down

	Subject / Started by	Replies / Views	Last post
0 Members and 17 Guests are viewing this board.
	Bear bullet 44 cal Saeco 240 grain vs lee 300 grain Started by bulletstuffer	7 Replies 1667 Views	July 30, 2011, 10:11:13 AM by anachronism
	Can't seem to dial in my 45-70 Started by tacotime	14 Replies 1682 Views	July 27, 2011, 05:59:10 AM by tacotime
	If you were going to buy one 30-30 mould Started by Sharps-Nut	17 Replies 2067 Views	July 24, 2011, 10:01:00 AM by anachronism
	Loading cast bullets in .405 Winchester, novice at this Started by The Shrink	5 Replies 1766 Views	July 23, 2011, 06:57:23 PM by Ranch13
	.30-30 cast loads Started by GH1	9 Replies 1952 Views	July 22, 2011, 04:13:04 PM by GH1
	Rule for load change switching jacketed to cast? Started by tacotime	7 Replies 1092 Views	July 22, 2011, 05:18:11 AM by jlchucker
	I got blisters on my fingers!!!! Started by Land_Owner	21 Replies 2248 Views	July 20, 2011, 03:14:20 AM by bulletstuffer
	LEAD smelting Question Started by GRAMPS 94	14 Replies 1498 Views	July 14, 2011, 10:57:26 AM by SHOOTALL
	Cast and Jacketed in the same barrel? Started by tacotime	14 Replies 1669 Views	July 14, 2011, 10:51:27 AM by tacotime
	Recomends for 180 LBT in Marlin 1895 cowboy Started by Ray Cover	1 Replies 893 Views	July 13, 2011, 01:42:23 AM by ratdog
	Heavy for caliber 45 Colt Buffalo Classic Handi-rifle cast boolits? Started by Land_Owner	16 Replies 2856 Views	July 10, 2011, 09:48:57 AM by Dinny
	30 cal mold freezing in sprue plate Started by gunther66	9 Replies 1581 Views	July 09, 2011, 06:24:15 AM by anachronism
	Test results Cast in Glock 40S&W Started by hornady	0 Replies 636 Views	July 07, 2011, 09:39:48 AM by hornady
	What is a good after - market barrel for the Glock? Started by Couger	8 Replies 1099 Views	July 07, 2011, 08:33:54 AM by Couger
	Cast Bullet Hollow Points? Started by powhs	25 Replies 5839 Views	July 05, 2011, 11:25:37 PM by ratdog
	Roof flashing lead Started by mechanic	5 Replies 1110 Views	July 05, 2011, 04:50:38 PM by Darrell Davis
	LBT Blue Soft Started by Northern Flatlander	3 Replies 1352 Views	July 03, 2011, 09:31:56 AM by geezerbiker
	Goodbye to Ranger Rick Started by bikerbeans	0 Replies 937 Views	June 25, 2011, 09:21:55 AM by bikerbeans
	Lead-How much longer? Started by greenrivers	5 Replies 1146 Views	June 24, 2011, 06:51:46 PM by nicholst55
	500 Wyoming Express Started by GH1	5 Replies 945 Views	June 23, 2011, 01:37:27 AM by GH1
	Oops! Wrong end in the melt pot. Started by Land_Owner	4 Replies 995 Views	June 07, 2011, 02:02:33 AM by Lloyd Smale
	Why don't they listen? Started by .22-5-40	4 Replies 1338 Views	June 06, 2011, 08:34:31 AM by mdi
	Hardness testing Started by AtlLaw	4 Replies 902 Views	June 03, 2011, 02:11:40 AM by Bob J
	Sizing for 9mm and 357 Started by texaspete	8 Replies 1457 Views	May 28, 2011, 06:04:09 PM by CherokeeT
	Lee-menting moulds and alloying Started by AtlLaw	16 Replies 2781 Views	May 26, 2011, 09:53:49 AM by SHOOTALL
	CHRISTmas came early Started by stimpylu32	6 Replies 1298 Views	May 19, 2011, 04:54:56 PM by stimpylu32
	Picking up Wheel Weights for Free Started by Dantes	4 Replies 1256 Views	May 15, 2011, 11:02:39 AM by 45-70.gov
	pin gage and cylinder Started by luckydawg13	2 Replies 830 Views	May 11, 2011, 08:13:32 AM by mdi
	Lee 4-20 Started by hornady	5 Replies 938 Views	May 09, 2011, 09:57:01 AM by greenrivers
	modifying a mold Started by hansg/Ups	1 Replies 688 Views	May 08, 2011, 01:53:27 AM by StrawHat

Pages: 1 ... 5 6 7 8 9 [10] 11 12 13 14 15 ... 86 Go Up

Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)

Locked Topic
Sticky Topic
Poll